LG-Ericsson iPECS eMG100 Programming Manual Download | Manualshive

Page: 575 / 718

background image

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

558

Table 4.4.13.6-1 ZONE ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

Local Number Digit

Count

CLI length is over this count then it is long distance call

otherwise it is local call.

(it is for incoming CLI)

00-30

0

Leading Zero

Insertion for Area

code

For an outgoing call, the system can insert a zero (‘0’) in

front of area code.

No

Yes

No

My Area Code

Insertion

For an outgoing call, the system can insert my area code in

the CLI.

No

Yes

No

Exceptional Conversion : for Outgoing Dial Number

Conversion Case #1 The first digits, up to four (4), dialed by the user can be

converted to a digit string of up to six (6) digits and may
include a plus (+) sign. For example if the “From” digits are

00 a

nd the “To” digits are +820, if the user dials

002233432, the system converts the number to +820

2233432.

From

(4-digits)

To (6-digits)

Conversion Case #2

Conversion Case #3

Conversion Case #4

Conversion Case #5

Exceptional Conversion : for Incoming CLI Number

Conversion Case #1 The first digits, up to four (4), received as the CLI can be

converted to a digit string of up to six (6) digits and may
include a plus (+) sign. For example if the “From” digits are
00 and the “To” digits are +820, if the user dials

002233432, the system converts the number to +820

2233432.

From

(4-digits)

To (6-digits)

Conversion Case #2

Conversion Case #3

Conversion Case #4

Normal Zone Management Information

Language Code

Language code of devices in the zone.

Language

Code

Nation

dependent

Codec Type

Assigns the codec employed by devices in the Zone.

System codec, G.711, G.723.1, G.729, G.722

Refer to

description

System

codec

RTP Relay Rule

Assigns when to use the packet relay function, with

“If

Need” the MPB will automatically determines when to use
packet relay, while “RTP Relay Group” will always

implement packet relay for RTP packets.

If need, Relay Group, Forced to Relay

Refer to

description

If need

1st RTP Relay

Device Slot Seq.

Assigns the local VOIU or VOIB IP channels that will be

used to implement packet relay for devices in the Zone.

eMG80/100:13, eMG800:19

Sequence

Number

Refer to

description

2nd RTP Relay

Device Slot Seq.

Back-up VoIP channels for RTP packet relay use in the

Zone.

eMG80/100:14, eMG800:NA

Sequence

Number

Refer to

description

VM Device Slot

Sequence

(VMIU/VMIB Slot

Sequence)

Assigns the UVMU/UVM/VMIU/VMIB used to support Voice

Mail for devices in the Zone. The UVMU/UVM/VMIU/VMIB

must be under control of the same MPB/UCP as the device

being assigned.

eMG80/100: 2 (1:15/2:16), eMG800: 3

Sequence

Number

Refer to

description

«
...
573
574
575
576
577
...
»

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS eMG100

Brand: Samsung Pages: 79

Brand: Samsung Pages: 88

Brand: Samsung Pages: 215

Brand: Samsung Pages: 155

Brand: Yeastar Technology Pages: 9

Brand: Talkswitch Pages: 334

Brand: Panasonic Pages: 98

Brand: Bogen Pages: 1

Brand: Sigma V Pages: 48

Brand: AT&T Pages: 7

Brand: AT&T Pages: 35

Brand: Alcatel Pages: 46

Brand: VTech Pages: 37

Brand: GE Pages: 100

Brand: Bea-fon Pages: 64

Brand: AT&T Pages: 40

DECT2080 Series

Brand: Uniden Pages: 68

Brand: Uniden Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands