LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 447 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

430

Table 4.4.6.3-2ACD GROUP ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

CIQ Route 1

When an ACD call is queued, the caller may be allowed to dial a

digit to exit the queue and route to another destination. The

alternate destination is based on the user-dialed digit and can be

a station, Station group, system-speed bin, or network station.

Dial the digit below for the type of destination and enter the

value associated with the destination.

1: Enter a station number.

2: Enter a Station group number.

3: Enter a system speed bin.

4: Enter a network station number

Not

selected

CIQ Route 2

CIQ Route 3

CIQ Route 4

CIQ Route 5

CIQ Route 6

CIQ Route 7

CIQ Route 8

CIQ Route 9

CIQ Route 0

ZAP Tone

Agents using a headset can have ACD calls connected to them

automatically preceded by a tone (Zap tone).

OFF

CIQ

Announcement

If enabled, queued callers receive the CIQ message (You are #

in queue) after the 1st and 2nd announcement.

OFF

Mailbox Message

Wait Station

When an ACD call overflows or routes to the VM group, a station

number is used to identify the Mailbox for the ACD group

messages

Station

number

Mailbox Password

The password associated with an ACD group Mailbox is defined

here. The password is used in conjunction with the ACD group

Mailbox as with a normal station.

Max. 12

digits

CIQ Display To

Agent - Mode

When an ACD call is in queue, the Call in queue information is

displayed in the LCD of agent and supervisor phones.

OFF

CIQ Page VM Slot

If the queued call count exceeds the threshold, the system plays

the CIQ Alert Announcement.

You can fill out the sequence number of UVM module for CIQ

Alert Announcement in case of being CPU Redundancy. The

sequence number of UVMU is used for CIQ Alert announcement

by default, but the UVMU is out of service during Redundancy

so that the sequence number of UVM is needed for happening

Redundancy.

Sequence

number

CIQ #1 Page Alert

-Threshold

If the queued call count exceeds the threshold, the system plays

the CIQ #1 Announcement to the CIQ #1 Page Zone after the

CIQ #1 Announcement Delay Timer. The announcement is

repeated at intervals of the CIQ #1 Announcement Repeat

Timer.

00-99

CIQ #1 Page Alert
–Announcement

Location

VSF announcement number for the CIQ #1 Announcement.

00-200

CIQ #1 Page Alert
– Page Zone

Page Zone to receive CIQ #1 Announcement.

eMG80/100:00~15 or00-40, eMG800:0~105, UCP:0~105

Refer to

description

CIQ #1 Page Alert

-Delay Time

Delay timer for CIQ #1 Announcement

000-180

015

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands