manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

Share
Download
LG-Ericsson iPECS eMG100 Programming Manual Download Page 282

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

265 

Table 4.4.2.2-1 Common Attributes 

ATTRIBUTE 

DESCRIPTION 

RANGE 

DEFAULT 

Station Web 

Language 

User can select the desired language for Station Web. 

English, Local language 

Refer to 

description 

English 

Lift Handset for 

page 

If an iPECS IP or LDP Phone user attempts to page using the 

speakerphone, pre-selection will be activated and the display 
shows “Lift Handset for Page when Lift Handset forPage is ON”. 

If Lift Handset for Page is OFF, then User can make page on 

speakerphone without lift handset. 

OFF 

ON 

ON 

Privacy 

If Privacy is ON, then any person could not barge-in to the station 

and also Attendant can

’t intrude to Station.   

Also, if Privacy is ON, any person can

’t forcefully disconnect the 

station. 

OFF 

ON 

OFF 

Collect call 

block 

This option enables each station to block a collect call by setting 

OFF. 

OFF 

ON 

OFF 

DSS LED 

service 

This option indicates whether to use the other station by showing 

LED of DSS button if the other station is assigned to DSS button.   

If this option is ON, the DSS LED light appears red.   

If this option is OFF, the LED DSS light is not available even 

though the station number is assigned to DSS button. 

OFF 

ON 

ON 

DSS LED 
service on 
other station

 

This option indicates whether DSS LED is updated or not on other 

station 

If it is ON then DSS button LED of other station is updated. If it is 

OFF then DSS button LED of other station is not updated 

OFF 

ON 

ON 

Stop 

Emergency 

page 

announcement 

If this is set to "After announcement", then system will keep 

playing the announcement regardless of calling party's status. 

By calling party, After announcement 

Refer to 

description 

By calling 

party 

Send LM IP to 

UC client 

If it is set to the available number, then system sends LM IP to UC 

premium client even though it is connected to CM. 

It is used for local survival. 

UCP:1-100, eMG800:1-32,eMG80/100: 1-15 

Refer to 

description 

 

Media Option 

Only audio path is connected when make internal call/answer. 

Both Audio and Video path is connected when make internal 

call/answer between LIP-9070/9071. 

Audio only, Audio & Video 

Refer to 

description 

Audio only 

Hot Desk 

Emergency 

Call Identity 

When a Hotdesk station makes an emergency call, the 

specification of co line seized and caller number(CLI) is used with 

a stations according to this option. 

 

Follow Logged-in Agent:

 Use Emergency CO Group and 

CLI of hotdesk logical user station. 

 

Follow Hot Desk Phone:

 Use Emergency CO Group and 

CLI of hotdesk physical phone the user logged-in. 

Refer to 

description 

Follow 

Logged-in 

Agent 

Hot Desk Page 

Identity

 

Page identity and page group and zone. 

 

Follow logged-in agent 

 

Hot desk phone

 

Refer to 

description 

Follow 

Logged-in 

Agent 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands