manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

The LG-Ericsson iPECS eMG100 is a highly efficient and innovative business communication system. Unlock its full potential with our comprehensive Programming Manual, available for free download on manualshive.com. This manual provides detailed instructions and insights to maximize the functionality of your device.

Share
Download
background image

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

35 

3.3.3 

Station Data 

–

PGM 110-125 

3.3.3.1 

Station Type -PGM 110 

Each station is assigned a type, which is used by the system to recognize the station‘s capabilities and default 
Flex button configuration. In addition, for the iPECS DSS/BLF Consoles, the associated station number is 
identified here. Note that the maximum of three (3) DSS Consoles(LIP DSS & LDP DSS) can be associated 
and connected to a station. 

PROCEDURE 

 

STATION TYPE ASSIGN 

ENTER STA RANGE 

Press the 

[PGM] 

button and dial 110. 

100-110 F1:TY F2:ASC 

IPKTU 

Use the dial-pad to enter a station range (Ex 100~110). For a single station, 

enter the same number twice; use this procedure for an iPECS DSS   

Select Flex button 1, to set the station type and, for iPECS DSS Consoles 

(types 2~4), Flex button 2 assigns the associated station. 

Use the dial-pad to enter desired data: 

-  4-1. For Flex button 1 (TYPE), enter the station TYPE; refer to 3.3.3.1

–1. 

111-111 F1:TYPE F2 :ASC 

DSS MAP2 : STA . . . . 

-  4-2. For Flex button 2 (Associated station), enter the number of the station 

used with the console. Flex button 2 is only available for iPECS DSS 

Consoles (Types 2~4), see Table 3.3.3.1-2 for default configurations. 

Press the 

[Save] 

button to store the data entries. 

 

Table 3.3.3.1-2 STATION TYPE ASSIGNMENT 

— (PGM 110) 

TYPE 

DESCRIPTION 

1 

IP KEYSET 

2 

DSS MAP 1 

3 

DSS MAP 2 

4 

DSS MAP 3 

5 

SLT (DTMF) 

6 

SLT (DTMF) 

– Voltage Message lamp 

7 

SLT (DTMF) 

– FSK Message lamp 

8 

SLT (DTMF) 

– Polarity Reversal Message lamp 

 

Table 3.3.3.1-1 CONSOLE BUTTON CONFIGURATION (PGM 110) 

MAP 

DEFAULT CONSOLE BUTTON CONFIGURATION 

MAP 1 

Button 1: Intrusion 

Button 2: All Call Page 

Button 3: Call Park 1 

Button 4: Station Group 1 

Button 5: Camp-On 

Button 6: Internal All Call Page 

Button 7: Call Park 2 

Button 8: Station Group 2 

Button 9: [Release] 

Button 10: Ext. All Call Page 

Button 11: Call Park 3 

Button 12: Station Group 3 

Buttons 13 ~ 48: Station Ports 100 ~ 135 

MAP 2 

Station Ports 136 ~ 183 

MAP 3 

Station Ports 184 ~ 231 

 

 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS eMG100

GE -295861 - Corded Desktop CID Itad User Manual preview
-295861 - Corded Desktop CID Itad
Brand: GE Pages: 44
Panasonic KX-TS520FX Operating Instructions preview
KX-TS520FX
Brand: Panasonic Pages: 2
Panasonic KX-TD500CE User Manual preview
KX-TD500CE
Brand: Panasonic Pages: 280
Panasonic KXTVS100 - VOICE MAIL SYSTEM Quick Installation Manual preview
KXTVS100 - VOICE MAIL SYSTEM
Brand: Panasonic Pages: 91
Panasonic KX-T336 Installation Instructions Manual preview
KX-T336
Brand: Panasonic Pages: 872
Panasonic Easa-Phone VA-208 Operating Instructions Manual preview
Easa-Phone VA-208
Brand: Panasonic Pages: 45
Panasonic Easa-Phone VA-208 Operating Instruction preview
Easa-Phone VA-208
Brand: Panasonic Pages: 45
Panasonic KX-TH102M Operating Instructions Manual preview
KX-TH102M
Brand: Panasonic Pages: 128
Panasonic KX-TD308 Installation Manual preview
KX-TD308
Brand: Panasonic Pages: 408
Yealink T53 Quick Start Manual preview
T53
Brand: Yealink Pages: 4
Panasonic KX-TD816AL User Manual Addendum preview
KX-TD816AL
Brand: Panasonic Pages: 67
Aastra Venture IP 480i Installation Manual preview
Venture IP 480i
Brand: Aastra Pages: 12
Unifone Small Office Installation And Programming Manual preview
Small Office
Brand: Unifone Pages: 96
Getek GKW06D Quick Manual preview
GKW06D
Brand: Getek Pages: 6
ATL Product Berkshire 400 Plus User Manual preview
Berkshire 400 Plus
Brand: ATL Product Pages: 4
AT&T HS8255 User Manual preview
HS8255
Brand: AT&T Pages: 51
Telongo LX210 User Manual preview
LX210
Brand: Telongo Pages: 6
AEI COMMUNICATIONS AFT-4100 Quick Installation Manual preview
AFT-4100
Brand: AEI COMMUNICATIONS Pages: 3

Brands by name

Popular brands

Load more brands