manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

The LG-Ericsson iPECS eMG100 is a highly efficient and innovative business communication system. Unlock its full potential with our comprehensive Programming Manual, available for free download on manualshive.com. This manual provides detailed instructions and insights to maximize the functionality of your device.

Share
Download
background image

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

362 

ATTRIBUTE   

DESCRIPTION 

RANGE 

DEFAULT 

External Noti. 

Cancel at 

Answer 

Option to cancel simultaneous ring or cancel on-going failover 

scenario when an external party answers the alarm ring 

 

Do not Cancel Other Trying Calls: leave all of on-going ring or 
retying calls 

 

Cancel All Other Trying Calls: cancel all of on-going ring or 
retying calls except answered calls 

 

Cancel All Except Prior Trying: cancel all except on-going ring 
or retying calls in prior Priority and answered calls 

Refer to 

description 

Cancel all 

other 

trying calls 

External 

Noti.Next Prio. 

On Failover 

Option for condition to start of failover scenario to next priority (from 

0 to 9)   

 

Immediately Go To Next: immediately implement next(less) 
priority at first busy/error/unanswered status of previous(prior) 
calls   

 

After Retry All Counts: implement next(less) priority after 
previous(prior) calls are all (re)tried and stopped by 
failure(busy/error/unanswered). 

Refer to 

description 

Immediate

ly go to 

next 

External 

Noti.Next Prio. 

On Answer 

Normally failover scenario is not implemented anymore if anybody 

answers the alarm ring.But if this timer is set(1-3600 sec.) then 

failover scenario is started/resumed after this duration even after 

somebody answers the alarm ring. 

0(immediate), 1-3600 sec 

Refer to 

description 

0 

Page Noti. 

Annc No. 

Play & Repeat VSF announcement to page group(s) 

Without a valid announcement, paging is not implemented 

0(not assign), 1-200 

Refer to 

description 

0 

Page Noti. 

Initial Delay 

Duration of delay before paging starts   

0(immediate), 1-3600 sec 

Refer to 

description 

0 

Page Noti. 

Page Urgency 

Level 

'0' is highest and '255' is lowest level 

Privilege to override other on-going page 

Case 1) page group busy 

-  If page group is occupied by other paging, higher level page will 

override the lower page, so the previous on-going page will be 

stopped 

Case 2) page member busy 

-  If a station is receiving a lower paging then it is overrided by a 

higher level paging, so the station will hear new paging 

Emergency, SoS pages are fixed to level '0' 

Normal page are fixed to level '255' 

Alarm page are programmable from level '0' to '255'   

0-255 

0 

Page Noti. 

Override By 

Urgency 

Override paging call only or override all calls. 

Override paged call only/ Override all calls 

Refer to 

description 

Override 

paged call 

only 

Page Noti. 

Override DND 

Override DND/Pre-selected-msg. status of a station 

ON/OFF 

OFF 

Page Noti. 

Page Repeat 

Count 

Repeat count of paging 

Total Play count : default(1) + repeat count(0-99) 

0-99 

2 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS eMG100

Jabra TOUR Datasheet preview
TOUR
Brand: Jabra Pages: 2
Yealink T21 Quick Reference Manual preview
T21
Brand: Yealink Pages: 2
Uniden EXI5560 - EXI 5560 Cordless Extension... Manual Del Usuario preview
EXI5560 - EXI 5560 Cordless Extension...
Brand: Uniden Pages: 48
Panasonic KX-TG9542 Operating Instructions Manual preview
KX-TG9542
Brand: Panasonic Pages: 88
JPS RTU-292 Installation And Operation Manual preview
RTU-292
Brand: JPS Pages: 116
ZETRON 30 Worldpatch Instruction Manual preview
30 Worldpatch
Brand: ZETRON Pages: 60
Unifone Small Office Installation And Programming Manual preview
Small Office
Brand: Unifone Pages: 96
TDS Polycom VVX410 Administrator'S Manual preview
Polycom VVX410
Brand: TDS Pages: 8
AT&T CL83101 User Manual preview
CL83101
Brand: AT&T Pages: 40
Q-Light SHDN30 Operating Manual preview
SHDN30
Brand: Q-Light Pages: 2
GE 27957GE1 User Manual preview
27957GE1
Brand: GE Pages: 100
Serene HD-60J Operating Manual preview
HD-60J
Brand: Serene Pages: 30
Easydive Leo3 Instructions preview
Leo3
Brand: Easydive Pages: 2
Aastra Meridian M5208 User Manual preview
Meridian M5208
Brand: Aastra Pages: 9
Telular PHONECELL SX3e AMPS User Manual preview
PHONECELL SX3e AMPS
Brand: Telular Pages: 26
Geemarc Amplidect350 User Manual preview
Amplidect350
Brand: Geemarc Pages: 236
Aristel AV SERIES Programming Manual preview
AV SERIES
Brand: Aristel Pages: 67
D-Link DWR-720/PW User Manual preview
DWR-720/PW
Brand: D-Link Pages: 59

Brands by name

Popular brands

Load more brands