LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 365 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

348

Table 4.4.5.1-1 SYSTEM ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

MSVC XML Port

The XML port used to support Web callback, call-through and

iPECS ClickCall application for MSVC (Mobile Service) must be

defined.

00001~

65535

7878

Security (option

for MSVC XML

Port)

It is security option for MSVC XML Port. (7878)
If it is “TLS1.2” then system accepts only TLS 1.2.

Other TLS1.1( or below) and SSL will be rejected.

“

Default” option is used for application compatibility as below.

UCS version that can support TLS1.2:



UCS Win Client: 6.1.5



UCS Mac Client: 6.1.3



UCS Android Client: 6.1.6



UCS iOS Client: 6.1.3

iPECS Click Call version that can support TLS1.2:



1.0Ar



2.0Ac

Report plus, CCS that can support TLS1.2:

(TBD: it will be supported in 2019 Q2)

So, if both UCS and report plus are used then “Default” should

be used before new report plus/CCS package is released.

DEFAULT

TLS 1.2

DEFAULT

IPCR Announce

for recording

warning

When ON, the IPCR server Call Recording notification

announcement is played to the caller in place of the warning

tone.

OFF

IPCR Announce

for only incoming

User can select IPCR Announce only

when it’s incoming by

setting ON.

OFF

Mobile EXT CO

Access

Password Check

When a mobile extension places an external call using an

iPECS CO/IP Line, the user may be required to enter a valid

Authorization code to place the call.

OFF

Hold key usage

on paging

When ON, the Hold key is used for paging.

OFF

Device Info

Request Interval

The system checks the status of each device with a polling

message at intervals of this timer.

15 ~ 255

(seconds)

Dial By Name

List

The Dial by Name feature can allow stations in any ICM tenancy

groups to call a station any in ICM Tenancy group. When

desired, Dial by Name can be limited to function within allowed

Tenancy calling groups, PGM 125.

All, Accessible ICM Group only

Refer to

description

ALL

Dial By System

Speed Name List

If this value is set to "Accessible System Speed Zone Only", the

system speed dial number of Accessiblesystemspeedzone

(System Speed Zone (232)) is displayed in {Dial by Name}.

All, Accessible System Speed Zone Only

Refer to

description

ALL

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands