LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 364 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

347

Table 4.4.5.1-1 SYSTEM ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

LCR Dial Tone

Detect

If this value is set to ON, the system first checks dial tone in

case on analog CO Lines then LCR dialing is completed. If no

dial tone is detected, the call is rerouted to Alternate DMT Index.

If LCR type is set to M13, LCR dial tone detect option is not

applied.

OFF

Mobile Phone

Presence

Service port

This is for an interface between eMG and external server that

sends http/xml data. Currently the first usage of this port is
‘mobile phone presence’ service.

If set to a valid port the presence service will be implemented

and the system will await messages for presence from the

external server.

00001~

65535

00000

Mobile Phone

Presence State

Sync

When the system receives presence information for a mobile

extension from external server, the system synchronizes the
station’s call state with this presence information. A busy

presence will set the station to busy.

OFF, DSS LED only, Station Status

Refer to

description

Station

Status

Mobile Phone

Presence Force

Idle Timer

The system will retu

rn a station’s state to idle if there is no

updated presence information from external server for the

duration of this timer.

0~3600

(Sec.)

Attendant

Password Usage

If this value is set to ON, system requests a password:

When a user enters Attendant program ([PGM] + 0,

When an Attendant enters Speed program,

When a user assigns attendant program code ([PGM] + 0) to

Flexible button,

OFF

Picked-up station

name usage

Name of picked up station is display when pickup internal call.

OFF

Display LCR

mode

Display “LCR MODE” when LCR is activated.

OFF

VM Notify to

Mobile Extension

over CO

If this value is set to ON, an analog Loop Start CO Line can be

used for the VM notification call to the Mobile Extension.

Disable

Enable

Disable

MODEM

Associated

Station/CO line

When a call is received by the assigned CO Line, the call is
routed to the system’s built-in modem. This option is available

only for eMG80/100& eMG800.

eMG80/100: STA/239, eMG800: STA/ 2199

CO/STA

Refer to

description

Display {MEET

ME} Soft button

If this value is set to OFF,

{MEET ME}

soft button is not

displayed during a paged.

OFF

Number of CLI

Wait List

The system check the status of each device with a polling

message periodically using this timer.

0-255

Emergency

Mailbox Station

When an Emergency Mailbox Station is assigned, an emergency

call placed by a station is recorded automatically to the assigned

mailbox.

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands