LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 177 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

160

Table 3.3.7.2-3 STATION GROUP ATTRIBUTES

— RING GROUPS (PGM 191)

BTN

ATTRIBUTE/DISPLAY

DESCRIPTION

RANGE

DEFAULT

RING 405 OVERFLOW DEST

S/H/V/SPD (Dial 1-4)

A call to the group rings at member stations

until the Overflow timer expires then the call

passes to the assigned Overflow

Destination.

1:Station, 2:Station group

3:VSF Announce, 4:System speed

Refer to

description

RING 405 OVERFLOW TMR

(000 - 600) : 180

A call to a ring group will continue to ring

stations in the group or be sent to the

assigned Overflow Destination after

expiration of the OVERFLOW Timer.

000~600

seconds

180

RING 405 WRAP-UP TMR

(000 - 999) : 002

After terminating any call, a Ring Group

member will be maintained in a busy state

for the duration of the WRAP-UP Timer.

000~999

seconds

002

RING 405 MUSIC SRC

(00

–37) : 01

A Music source is assigned so that calls to

the group will receive audio from the

assigned source in place of ring-back tone.



00: Ring-back



01: Int music



02: Ext music



03: VSF MOH



04~08: SLTMOH1~5



09~37: VSFMOH2~30

Refer to

description

RING 405 MAX QUE C-CNT

(00-99) : 99

When the number of calls queued is

reached, new calls will receive error tone

and be disconnected after the VSF AA

announcement, if assigned, is played.

00-99

RING 405 MBR FORWARD

(1 : ON/ 0: OFF) : ON

A member activating Call Forward may be

placed in an unavailable state for hunt

group calls (ON). When OFF, group calls

are sent to the member as normal.

0: OFF

1: ON

MAILBOX MSG WAIT STA

. . . .

When a group calls overflows or routes to

the VM group, a station number is used to

identify the Mailbox for the Ring group

messages.

Station

….

MAILBOX PASSWORD

…………

The password associated with a group

Mailbox is defined here. The password is

used in conjunction with the Ring group as

with a normal station.

12 digits

….

RING 405 FORCED DEST

S/H/V/SPD (DIAL 1-4)

When a call is delivered to the group the

system can redirect the call to the Forced

destination if enabled under button 16

below.

1:Station, 2:Station group
3:VSF Announce, 4:System speed

Refer to

description

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands