LG-Ericsson iPECS eMG100 Programming Manual Download

Page: 409 / 718

iPECS eMG80/100& eMG800 & UCP & vUCP
Administration and Programming Manual

Issue 2.3

392

Table 4.4.5.25-1 SMDR ATTRIBUTES

ATTRIBUTE

DESCRIPTION

RANGE

DEFAULT

Print Incoming Call

The system can output records for Incoming calls as well as

outgoing calls.If enabled, incoming as well as outgoing calls are

recorded.

OFF

Print Lost Call

When incoming call records are enabled, the system can also

provide records for unanswered incoming (abandoned) calls.

OFF

Records In Detail

The system can output detailed call records (ON) or summary

call information (total number of calls, cost and cost for each

station).

OFF

Hidden Dialed

Digit

For security purposes, digits dialed for an outgoing call can be
hidden and replaced with “*”. This field defines the number of

digits to hide. The Dialed Digit Hide Option below defines

whether leading or trailing digits are hidden The station must be

assigned for SMDR Hidden digits in

‘Common Attributes

section’.

0~9

Dialed Digit Hide

Option

When “HIDDEN DIALED DIGIT” is enabled, above, this field

determines if leading or trailing digits are hidden.

Right/

Left

Right

SMDR Currency

Unit

The unit of currency used for call cost can be identified with 3-

characters for easy reference.

Max. 3

characters

SMDR Cost Per

Metering Pulse

When call metering is provided by the PSTN, the cost per

metering pulse can be assigned.

6-digits

000000

SMDR Decimal

Location

This value determines the position of the decimal in the Cost per

Pulse entry above, starting from the right most digits.

0~5

Start Timer

To allow for call set-

up times through the PSTN, a “Valid call

timer” can be set.

000~250

(msec)

Long Distance

Code

For SMDR and COS purposes, five (5) Long Distance codes of

up to two (2) digits each can be assigned. If dialed as the 1st

digits, the call is considered an LD call.

5 two digit LD codes,use * as wild card(any digit)

Refer to

description

SMDR CLI or Ring

Service I

For incoming calls, the system will send the defined data item for
“Field I”. The data item may be CLI, CPN or Ring Service Time.

Note the User dialed number is always provided for an outgoing

call.

RING/

CLI/

CPN

RING

SMDR

Ring/CLI/CPN

Service II

For incoming calls, the system will send the defined data item for
“Field II”. The data item may be CLI, CPN or Ring Service Time.

RING/

CLI/

CPN/

None

Print MSN

For an ISDN call involving an MSN number, the MSN number

Information can be included in the SMDR Record.

OFF

Print Serial No

Each SMDR Record can include a record number starting at 1

and incrementing until the records are deleted. The record

number will reset to 1 when SMDR capacity is reached or SMDR

Mail Auto Delete Set is enabled under System Attributes.

OFF

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands

LG-Ericsson iPECS eMG100, Programming Manual

Search results

Summary of Contents for iPECS eMG100

Reviews:

Related manuals for iPECS eMG100

Brands by name

Popular brands