manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

Share
Download
LG-Ericsson iPECS eMG100 Programming Manual Download Page 492

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

475 

Table 4.4.8.3-1 SIP CO ATTRIBUTES 

ATTRIBUTE   

DESCRIPTION 

RANGE 

DEFAULT 

ID Option 

Caller ID 

Selection 

For the purposes of display and ICLID call routing, iPECS employ 
this header as the “Caller ID”. 

P-Asserted-ID, Remote-Party-D, From ID 

Refer to 

description 

P-Asserted-

ID 

Display Caller 

Name(Though 

Id is 

Anonymous) 

Even though the User ID is Anonymous, the system can display 
the SIP “From” header “Display Name” field for the call. 

No 

Yes 

No 

Called ID 

Selection 

For the purposes of call routing, the “SIP Request” or “To” header 

wil

l be employed by the system as the “Called Party ID”. 

Request URI, To ID 

Refer to 

description 

Request 

URI 

SIP Timer set 

T1 Timer 

First retransmission timer in case of No Reply. 

0.5 / 1 / 2   0.5 (Sec) 

Miscellaneous set 

Drop Busy 

Station 

While busy, the system can be configured to terminate a station 

call, and accept and connect any new call from the SIP Trunk. For 

special use, it is available only in Italy. 

No 

Yes 

No 

Ignore INBAND 

DTMF 

In some situations, DTMF tones from the connected party may be 

received along with the DTMF Type specified above. This can 

cause errors in detection such as double digits. In this case, the 

system can be configured to ignore Inband DTMF signals. Note 
do not disable Inband signals if selected as the “DTMF Type” 

above as this may disable DTMF detection. 

No 

Yes 

No 

SIP Trunk 

Group 

Multiple SIP User ID ranges may register with the SIP CO, for 

example, SIP COs from different providers. When different SIP 

User ID ranges are required on a SIP CO, a different SIP Trunk 

Group should be assigned to each range. Note this has no 

relationship with the CO/IP Line Group. 

0~71 (0:Normal, 1-71:Check To header) 

Refer to 

description 

0 

Send Refer for 

Transfer 

The system can employ the SIP Refer method to forward or 

transfer incoming calls to a

n “Off-net” location if supported by the 

SIP Service Provider. 

No 

Yes 

No 

CN Payload 

Insert 

When Comfort Noise generation is desired, the system will 

provide a Comfort Noise Payload during periods of silence. 

No 

Yes 

No 

Ignore 180 

after 183 

If the option is Yes, an appropriate ringback tone may be played 

to the calling party when the called party's phone is alerting 

without changing the internal or system ring back tone. For 

example, when placing a call from USA to Korea, a Korean 

ringback tone is heard by the caller. 

No 

Yes 

No 

Add 
“user=phone” 

parameter 

For outgoing SIP call, "user=phone" will be added in Request URI 

of INVITE. 

No 

Yes 

No 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands