manualshive.com logo in svg

LG-Ericsson iPECS eMG100, Programming Manual

The LG-Ericsson iPECS eMG100 is a highly efficient and innovative business communication system. Unlock its full potential with our comprehensive Programming Manual, available for free download on manualshive.com. This manual provides detailed instructions and insights to maximize the functionality of your device.

Share
Download
background image

iPECS eMG80/100& eMG800 & UCP & vUCP 
Administration and Programming Manual 

Issue 2.3 

473 

Table 4.4.8.3-1 SIP CO ATTRIBUTES 

ATTRIBUTE   

DESCRIPTION 

RANGE 

DEFAULT 

External CODEC Priority Configuration 

1st ~5th priority 

1st. priority, 2nd. Priority, 3rd. priority, 4th. Priority, 5th. Priority 

If specify priority to a specific CODEC then it will work for 

negotiation RTP data.If only 1st. priority is specified and the 

others are none, then it will work as single CODEC only does 

None/ g.711-u/ g.711-a/ g.723.1/ g.729/ g.729-a/ g.722 

Refer to 

description 

none 

SIP Call Setup Failover Option 

Call Setup No 

Response 

When the system initiates a SIP Trunk call and receives no 

response from the SIP proxy server, after expiration of this timer 

the SIP call is canceled and a Fail-over call placed on the Fail-

over CO/IP Line group specified below. Note the timer can be set 

at 3 to 15 seconds 

and ‘0’, which disables Fail-over. 

0, 3 ~ 15 

sec 

5sec 

Failover CO 

Group Number 

When the system attempts to initiate a SIP Trunk call and the SIP 

Trunk is in an OOS state or the SIP proxy server does not 

respond in the No Response time above, the system will cancel 

the SIP call and place a call over a CO/IP Line from this group. 

eMG80/100:1 ~ 21,eMG800/UCP:1~201 

Refer to 

description 

none 

SIP Session Timer 

Session Timer 

Usage 

During a SIP call or “session”, there are no signaling packets sent 

or received from the SIP Call server. In order to assure a session 

is still active, the system can periodically send an Option message 

that the SIP Call server should acknowledge. 

ON/OFF 

OFF 

Session Timer 

Value 

When “Session Timer Usage” is enabled, the system will verify the 

session at this timer interval. 

90~ 3600 

360 

Min SE 

During negotiation with “Session Timer Usage” enabled, the 

system will use this value as the minimum Session expiration 

timer and will not respond to a SIP Option message prior to 

expiration of this timer. 

90~ 3600 

90 

URI Formatting and Rules 

General Formatting 

To Field 

Method 

The SIP “To:” header is formatted using the SIP or Telephony 

method as shown below. 

 

SIP method 
To: < sip:[Number]@[Domain];user=phone > 

 

Telephony method 
To: < tel:+[Number] >Domain 

Refer to 

description 

SIP: 

method 

Numbering 

Format 

When assigned the Telephony method for the 

“To” header, the 

number format can be: 

 

Local

 - [tel:+Number]@[Domain] 

 

Global

(+E164) - [tel:+E.164 Address]@[Domain] 

E.164 Address:  Area Code + Number 

Refer to 

description 

Local 

Summary of Contents for iPECS eMG100















































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for iPECS eMG100

NEC Univerge SV9100 User Training preview
Univerge SV9100
Brand: NEC Pages: 6
NEC Univerge SV9100 Voicemail Administration Manual preview
Univerge SV9100
Brand: NEC Pages: 10
NEC Univerge UM8000 Quick Manual preview
Univerge UM8000
Brand: NEC Pages: 7
NEC SL1000 Getting Started Manual preview
SL1000
Brand: NEC Pages: 46
NEC SL1000 Technical Training Manual preview
SL1000
Brand: NEC Pages: 39
NEC Dterm I Series Quick Reference Manual preview
Dterm I Series
Brand: NEC Pages: 5
NEC SL1000 Hardware Manual preview
SL1000
Brand: NEC Pages: 150
NEC Univerge SV9100 User Manual preview
Univerge SV9100
Brand: NEC Pages: 77
NEC Dterm I Series Owner'S Manual preview
Dterm I Series
Brand: NEC Pages: 56
Doro PhoneEasy Display 312C Manual preview
PhoneEasy Display 312C
Brand: Doro Pages: 20
Jumbo 1203879 User Manual preview
1203879
Brand: Jumbo Pages: 4
Aastra Aastra 620d User Manual preview
Aastra 620d
Brand: Aastra Pages: 22
NEC DSX 1093099 Feature Handbook preview
DSX 1093099
Brand: NEC Pages: 190
AGFEO ST 31 User Manual preview
ST 31
Brand: AGFEO Pages: 20
Bestway Hydro-Force 62195 Manual preview
Hydro-Force 62195
Brand: Bestway Pages: 6
Moshi ionsuit Important Notes & Instructions preview
ionsuit
Brand: Moshi Pages: 7
Panasonic KX-TGF372AZS Operating Instructions Manual preview
KX-TGF372AZS
Brand: Panasonic Pages: 84
Uniden EXAI 3248 Series Owner'S Manual preview
EXAI 3248 Series
Brand: Uniden Pages: 68

Brands by name

Popular brands

Load more brands