Lenovo Flex System x220 Installation And Service Manual Download Page 599 | Manualshive

Page: 599 / 714

background image

Complete the following steps:

1. Verify that matching processors are installed in the correct processor sockets.

2. Check the IBM support site for an applicable service bulletin or firmware update that applies to

this processor error.

3.

Replace the system board.

Related links

–

“Removing a microprocessor and heat sink” on page 675

–

“Installing a microprocessor and heat sink” on page 678

–

“Removing the system-board assembly” on page 683

–

“Installing the system-board assembly” on page 684

•

I.2018002 [I.2018002] The device found at Bus % Device % Function % could not be configured

due to resource constraints. The Vendor ID for the device is % and the Device ID is %.

Explanation:

OUT_OF_RESOURCES (PCI Option ROM)

Severity

Info

User Response

Complete the following steps:

1. If this PCIe device and/or any attached cables were recently installed, moved, serviced or

upgraded, reseat the adapter and any attached cables.

2. Check the IBM support site for any applicable service bulletin or UEFI or adapter firmware

update that applies to this error. NOTE: It may be necessary to disable unused option ROMs
from UEFI F1 setup or ASU or using adapter manufacturer utilities so that adapter firmware
can be updated.

3. Move the adapter to a different slot. If a slot is not available or error recurs, replace the adapter.

4. If the adapter was moved to a different slot and the error did not recur, verify that this is not a

system limitation. Then replace the system board. Also, if this is not the initial installation and the
error persists after adapter replacement, replace the system board.

Related links

–

“Removing an I/O expansion adapter” on page 666

–

“Installing an I/O expansion adapter” on page 667

–

“Removing the system-board assembly” on page 683

–

“Installing the system-board assembly” on page 684

•

I.2018003 [I.2018003] A bad option ROM checksum was detected for the device found at Bus %

Device % Function %. The Vendor ID for the device is % and the Device ID is %.

Explanation:

ROM CHECKSUM ERROR

Severity

Info

User Response

Complete the following steps:

Troubleshooting

591

«
...
597
598
599
600
601
...
»

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Flex System x220

Brand: IBM Pages: 214

ShareCenter Pro DNS-1200-05

Brand: D-Link Pages: 68

ApplianceStor 15MT

Brand: Rasilient Pages: 30

Brand: AIC Pages: 88

Brand: IBM Pages: 491

Brand: EMC Pages: 34

Brand: Cabletron Systems Pages: 100

SUPERSERVER 5025M-UR

Brand: Supermicro Pages: 130

Intesis IBMBSDAL0640000

Brand: HMS Networks Pages: 39

Brand: 3onedata Pages: 3

Brand: LOOQS Pages: 69

Brand: BRONKHORST Pages: 19

Brand: Cisco Pages: 2

Brand: Lantronix Pages: 135

Brand: Inspur Pages: 200

Brand: Godex Pages: 31

Brand: Intel Pages: 60

Brand: GIGA-BYTE TECHNOLOGY Pages: 90

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands