Lenovo Flex System x220 Installation And Service Manual Download Page 195

Page: 195 / 714

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

180-801-000 : Check-point Panel Test Aborted

Check-point Panel Test Aborted. BMC is unable to verify that the operator information panel cable is
connected.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Inspect and reseat operator information panel cable at both ends.

2. Verify that the Baseboard Management Controller (BMC) is working.

3. Run the test again.

4. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

180-901-000 : Check-point Panel Test Failed

Check-point Panel Test Failed. Operator reported incorrect display.

Recoverable

Severity

Error

Serviceable

Chapter 6

Troubleshooting

187

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands