Lenovo Flex System x220 Installation And Service Manual Download Page 276

Page: 276 / 714

A user configured a Server Power action at a specific time

May also be shown as 4000005200000000 or 0x4000005200000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0082

User Response

Information only; no action is required.

•

40000053-00000000 : Server [arg1] scheduled for every [arg2] at [arg3] by user [arg4].

A user configured a recurring Server Power Action

May also be shown as 4000005300000000 or 0x4000005300000000

Severity

Info

Serviceable

Automatically notify support

Alert Category

none

SNMP Trap ID

CIM Information

Prefix:

IMM

ID:

0083

User Response

Information only; no action is required.

•

40000054-00000000 : Server [arg1] [arg2] cleared by user [arg3].

A user cleared a Server Power Action.

May also be shown as 4000005400000000 or 0x4000005400000000

268

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands