Lenovo Flex System x220 Installation And Service Manual Download Page 678

Page: 678 / 714

Step 2.

Connect the cable on the system board.

Step 3.

Align the light path diagnostics panel with the bracket.

Step 4.

Press the light path diagnostics panel securely in the bracket.

After you install the light path diagnostics panel, complete the following steps:

1. Install the cover onto the compute node (see “Installing the compute node cover” on page 644 for

instructions).

2. Install the compute node into the chassis (see “Installing a compute node in a chassis” on page 639

for instructions).

Removing the RFID tag

Use this information to remove the RFID tag from the bezel.

Before you remove the RFID tag, read “Safety” on page iii and “Installation guidelines” on page 637.

To remove the RFID tag, complete the following steps.

0000000000000

000000000

00000000000000000000000000

670

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands