Lenovo Flex System x220 Installation And Service Manual Download Page 590

Page: 590 / 714

A fatal bus error is no longer detected in the I/O expansion adapter in PCIe adapter slot 4 in the PCI
expansion unit.

May also be shown as 816f0a132c04ffff or 0x816f0a132c04ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0245

User Response

Information only; no action is required.

•

816f0a13-3101ffff : Bus PEN Slot1 has recovered from a Fatal Bus Error.

A fatal bus error is no longer detected in the I/O expansion adapter in PCIe adapter slot 1 in the PCI
expansion unit.

May also be shown as 816f0a133101ffff or 0x816f0a133101ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0245

User Response

Information only; no action is required.

•

816f0a13-3102ffff : Bus PEN Slot2 has recovered from a Fatal Bus Error.

582

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands