Lenovo Flex System x220 Installation And Service Manual Download Page 576

Page: 576 / 714

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0143

User Response

Information only; no action is required.

•

816f090c-2004ffff : memory device 4 in Group 1 on Subsystem System Memory is no longer

Throttled

DIMM throttling in DIMM connector 4 has been turned off.

May also be shown as 816f090c2004ffff or 0x816f090c2004ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0143

User Response

Information only; no action is required.

•

816f090c-2005ffff : memory device 5 in Group 1 on Subsystem System Memory is no longer

Throttled

DIMM throttling in DIMM connector 5 has been turned off.

May also be shown as 816f090c2005ffff or 0x816f090c2005ffff

Severity

Info

Serviceable

568

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands