Lenovo Flex System x220 Installation And Service Manual Download Page 588

Page: 588 / 714

This message is for the use case when an implementation has detected that a system has recovered
from a Bus Fatal Error.

May also be shown as 816f0a130301ffff or 0x816f0a130301ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0245

User Response

CPU 1 PECI :

•

816f0a13-0302ffff : Bus [SensorElementName] has recovered from a Fatal Bus Error.

This message is for the use case when an implementation has detected that a system has recovered
from a Bus Fatal Error.

May also be shown as 816f0a130302ffff or 0x816f0a130302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0245

User Response

CPU 2 PECI :

•

816f0a13-2401ffff : Bus [SensorElementName] has recovered from a Fatal Bus Error.

580

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands