Lenovo Flex System x220 Installation And Service Manual Download Page 470

Page: 470 / 714

Alert Category

Critical - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

Information only; no action is required.

•

81010b01-3701ffff : Numeric sensor Inlet Temp going high (upper non-recoverable) has deasserted.

The previously high inlet temperature has returned to below its specified threshold.

May also be shown as 81010b013701ffff or 0x81010b013701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0499

User Response

Information only; no action is required.

•

81010b01-3702ffff : Numeric sensor PEN Inlet Temp going high (upper non-recoverable) has

deasserted.

The previously high inlet temperature has returned to below its specified threshold.

May also be shown as 81010b013702ffff or 0x81010b013702ffff

Severity

Info

Serviceable

Automatically notify support

462

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands