Lenovo Flex System x220 Installation And Service Manual Download Page 482

Page: 482 / 714

May also be shown as 810702170b05ffff or 0x810702170b05ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

Information only; no action is required.

•

81070217-0b81ffff : Sensor PEN FHR Empty has transitioned to a less severe state from critical.

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702170b81ffff or 0x810702170b81ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

Information only; no user action required.

•

81070217-0b82ffff : Sensor PEN LPR Empty has transitioned to a less severe state from critical.

This message is for the use case when an implementation has detected a Sensor transition to less
severe from critical.

May also be shown as 810702170b82ffff or 0x810702170b82ffff

474

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands