Lenovo Flex System x220 Installation And Service Manual Download Page 229

Page: 229 / 714

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-901-000 : IANet:EEPROM Test Failed

A failure was detected during the EEPROM test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check component firmware level and upgrade if necessary. The installed firmware level can be

found in the DSA Diagnostic Event Log within the Firmware/VPD section for this component.

2. Rerun the test.

3. If failure remains, refer to "Troubleshooting by symptom" in the system "Installation and Service

Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

406-902-000 : IANet:FIFO Test Failed

A failure was detected during the FIFO test.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

Chapter 6

Troubleshooting

221

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands