Lenovo Flex System x220 Installation And Service Manual Download Page 495

Page: 495 / 714

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0531

User Response

Information only; no action is required.

•

81070601-2c03ffff : Sensor PEN MExp 3 temp has deasserted the transition to non-recoverable.

The previously high PEN Mezzanine Expansion card temperature has returned below its specified
threshold.

May also be shown as 810706012c03ffff or 0x810706012c03ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0531

User Response

Information only; no action is required.

•

81070601-2c04ffff : Sensor PEN MExp 4 temp has deasserted the transition to non-recoverable.

The previously high PEN Mezzanine Expansion card temperature has returned below its specified
threshold.

May also be shown as 810706012c04ffff or 0x810706012c04ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

Chapter 6

Troubleshooting

487

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands