Lenovo Flex System x220 Installation And Service Manual Download Page 169

Page: 169 / 714

9. If the failure remains, refer to "Troubleshooting by symptom" in the system "Installation and

Service Guide" for the next corrective action.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-907-000 : Tape Test Failed

An error was found in the block address somewhere.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-908-000 : Tape Test Failed

An error was found in getting tape capacity.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Make sure that medium is present.

2. Clean the tape drive using the appropriate cleaning media and install new media.

Related links

Chapter 6

Troubleshooting

161

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands