Lenovo Flex System x220 Installation And Service Manual Download Page 525

Page: 525 / 714

CIM Information

Prefix:

PLAT

ID:

0169

User Response

Information only; no action is required.

•

816f020d-0406ffff : Failure no longer Predicted on drive Drive 6 for array

[ComputerSystemElementName].

Failure of hard disk drive 6 is no longer predicted.

May also be shown as 816f020d0406ffff or 0x816f020d0406ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0169

User Response

Information only; no action is required.

•

816f020d-0407ffff : Failure no longer Predicted on drive Drive 7 for array

[ComputerSystemElementName].

Failure of hard disk drive 7 is no longer predicted.

May also be shown as 816f020d0407ffff or 0x816f020d0407ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Chapter 6

Troubleshooting

517

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands