Lenovo Flex System x220 Installation And Service Manual Download Page 497

Page: 497 / 714

Prefix:

PLAT

ID:

0536

User Response

Information only; no action is required.

•

81090112-2101ffff : Device [LogicalDeviceElementName] has been disabled.

An IPMI or SNMP Account has been disabled.

May also be shown as 810901122101ffff or 0x810901122101ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0539

User Response

Information only; no action required.

•

810b010c-2581ffff : Redundancy Lost for Backup Memory has deasserted.

This message is for the use case when Redundacy Lost has deasserted.

May also be shown as 810b010c2581ffff or 0x810b010c2581ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0803

User Response

Information only; no action is required.

Chapter 6

Troubleshooting

489

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands