Lenovo Flex System x220 Installation And Service Manual Download Page 79

Page: 79 / 714

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA memory stress test results

The following messages can result when you run the memory stress test.

Test results for the DSA memory stress test

The following messages can result when you run the DSA memory stress test.

•

202-000-000 : MemStr Test Passed

Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

202-801-000 : MemStr Test Aborted

Internal program error.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Turn off and restart the system.

2. Make sure that the DSA Diagnostic code is at the latest level.

Chapter 6

Troubleshooting

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands