Lenovo Flex System x220 Installation And Service Manual Download Page 524

Page: 524 / 714

CIM Information

Prefix:

PLAT

ID:

0169

User Response

Information only; no action is required.

•

816f020d-0404ffff : Failure no longer Predicted on drive Drive 4 for array

[ComputerSystemElementName].

Failure of hard disk drive 4 is no longer predicted.

May also be shown as 816f020d0404ffff or 0x816f020d0404ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0169

User Response

Information only; no action is required.

•

816f020d-0405ffff : Failure no longer Predicted on drive Drive 5 for array

[ComputerSystemElementName].

Failure of hard disk drive 5 is no longer predicted.

May also be shown as 816f020d0405ffff or 0x816f020d0405ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Predicted Failure

SNMP Trap ID

516

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands