Lenovo Flex System x220 Installation And Service Manual Download Page 547

Page: 547 / 714

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0145

User Response

Information only; no action is required.

•

816f050c-2008ffff : Memory Logging Limit Removed for DIMM 8 on Subsystem

[MemoryElementName].

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Removed.

May also be shown as 816f050c2008ffff or 0x816f050c2008ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Warning - Memory

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0145

User Response

Information only; no action is required.

•

816f050c-2009ffff : Memory Logging Limit Removed for DIMM 9 on Subsystem

[MemoryElementName].

This message is for the use case when an implementation has detected that the Memory Logging Limit
has been Removed.

May also be shown as 816f050c2009ffff or 0x816f050c2009ffff

Chapter 6

Troubleshooting

539

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands