Lenovo Flex System x220 Installation And Service Manual Download Page 585

Page: 585 / 714

•

816f0a0c-2007ffff : An Over-Temperature Condition has been removed on the memory device

7 in Group 1 on Subsystem System Memory.

The DIMM in DIMM connector 7 is no longer in an overtemperature condition.

May also be shown as 816f0a0c2007ffff or 0x816f0a0c2007ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0147

User Response

Information only; no action is required.

•

816f0a0c-2008ffff : An Over-Temperature Condition has been removed on the memory device

8 in Group 1 on Subsystem System Memory.

The DIMM in DIMM connector 8 is no longer in an overtemperature condition.

May also be shown as 816f0a0c2008ffff or 0x816f0a0c2008ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0147

User Response

Information only; no action is required.

Chapter 6

Troubleshooting

577

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands