Lenovo Flex System x220 Installation And Service Manual Download Page 340

Page: 340 / 714

The previously high temperature of the I/O expansion adapter in I/O expansion connector 2 has returned
to below its specified threshold.

May also be shown as 800704012c02ffff or 0x800704012c02ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0526

User Response

Information only; no action is required.

•

80070401-2c03ffff : Sensor PEN MExp 3 Temp has transitioned to non-critical from a more severe

state.

The previously high temperature of the PEN Mezzanine Expansion adapter in I/O expansion connector
3 has returned to below its specified threshold.

May also be shown as 800704012c03ffff or 0x800704012c03ffff

Severity

Warning

Serviceable

Automatically notify support

Alert Category

Warning - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0526

User Response

Information only; no action is required.

•

80070401-2c04ffff : Sensor PEN MExp 4 has transitioned to non-critical from a more severe state.

332

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands