Lenovo Flex System x220 Installation And Service Manual Download Page 480

Page: 480 / 714

•

81070202-0701ffff : Sensor Planar Fault has gone from Criitical state to a less severe state.

A failure is no longer detected in the system board.

May also be shown as 810702020701ffff or 0x810702020701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

Information only; no action is required.

•

81070202-1901ffff : Sensor PEN Planar Fault has transitioned to a less severe state from critical.

A failure is no longer detected in the PEN Planar board.

May also be shown as 810702021901ffff or 0x810702021901ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Voltage

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0523

User Response

Information only; no action is required.

•

8107020f-2582ffff : Sensor No I/O Resources has transitioned to a less severe state from critical.

472

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands