Lenovo Flex System x220 Installation And Service Manual Download Page 575

Page: 575 / 714

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0143

User Response

Information only; no action is required.

•

816f090c-2002ffff : memory device 2 in Group 1 on Subsystem System Memory is no longer

Throttled

DIMM throttling in DIMM connector 2 has been turned off.

May also be shown as 816f090c2002ffff or 0x816f090c2002ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

System - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0143

User Response

Information only; no action is required.

•

816f090c-2003ffff : memory device 3 in Group 1 on Subsystem System Memory is no longer

Throttled

DIMM throttling in DIMM connector 3 has been turned off.

May also be shown as 816f090c2003ffff or 0x816f090c2003ffff

Severity

Info

Chapter 6

Troubleshooting

567

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands