Lenovo Flex System x220 Installation And Service Manual Download Page 179

Page: 179 / 714

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Verify that the GPU is seated in the PCIe slot correctly by reseating the GPU. Then power cycle

the system.

2. Verify that the power connectors to the GPU are connected firmly. Then power cycle the system.

3. Run nvidia-smi -q In some cases this will report a poorly connected power cable.

4. Rerun the diagnostics, using the same GPU, on system that is known to be working. A variety of

system issues can cause diagnostic failure.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

409-906-000 : Nvidia::DiagnosticServiceProvider::Binomial Test Failed

Nvidia GPU Binomial Test Failed.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Verify that the GPU is seated in the PCIe slot correctly by reseating the GPU. Then power cycle

the system.

2. Verify that the power connectors to the GPU are connected firmly. Then power cycle the system.

3. Run nvidia-smi -q In some cases this will report a poorly connected power cable.

4. Rerun the diagnostics, using the same GPU, on system that is known to be working. A variety of

system issues can cause diagnostic failure.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

Chapter 6

Troubleshooting

171

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands