Lenovo Flex System x220 Installation And Service Manual Download Page 170

Page: 170 / 714

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA hard drive test results

The following messages can result when you run the hard drive test.

Test results for the DSA hard drive test

The following messages can result when you run the DSA hard drive test.

•

217-000-000 : HDD Test Passed

HDD Stress Test Passed.

Recoverable

Severity

Event

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

217-800-000 : HDD Test Aborted

HDD Test Aborted. The test was canceled.

Recoverable

Severity

Warning

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check cable connections.

2. Rerun the test.

3. Verify that Hard drive supports self test and self test logging.

162

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands