Lenovo Flex System x220 Installation And Service Manual Download Page 506

Page: 506 / 714

May also be shown as 816f00131701ffff or 0x816f00131701ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0223

User Response

Information only; no action is required.

•

816f0021-2201ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName].

This message is for the use case when an implementation has detected a Fault condition in a slot has
been removed. No Op ROM Space.

May also be shown as 816f00212201ffff or 0x816f00212201ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Other

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0331

User Response

Information only; no action is required.

•

816f0021-2582ffff : Fault condition removed on slot [PhysicalConnectorElementName] on system

[ComputerSystemElementName].

498

Flex System x220 Compute Node Installation and Service Guide

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands