Lenovo Flex System x220 Installation And Service Manual Download Page 521

Page: 521 / 714

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0045

User Response

Information only; no action is required.

•

816f0207-0302ffff : CPU 2 has Recovered from FRB1/BIST condition.

This message is for the use case when an implementation has detected a Processor Recovered -
FRB1/BIST condition.

May also be shown as 816f02070302ffff or 0x816f02070302ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - CPU

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0045

User Response

Information only; no action is required.

•

816f0207-2584ffff : [ProcessorElementName] has Recovered from FRB1/BIST condition.

This message is for the use case when an implementation has detected a Processor Recovered -
FRB1/BIST condition. All CPUs. One of CPUs.

May also be shown as 816f02072584ffff or 0x816f02072584ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Chapter 6

Troubleshooting

513

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands