Lenovo Flex System x220 Installation And Service Manual Download Page 587

Page: 587 / 714

•

816f0a0c-200bffff : An Over-Temperature Condition has been removed on the memory device

11 in Group 1 on Subsystem System Memory.

The DIMM in DIMM connector 11 is no longer in an overtemperature condition.

May also be shown as 816f0a0c200bffff or 0x816f0a0c200bffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0147

User Response

Information only; no action is required.

•

816f0a0c-200cffff : An Over-Temperature Condition has been removed on the memory device

12 in Group 1 on Subsystem System Memory.

The DIMM in DIMM connector 12 is no longer in an overtemperature condition.

May also be shown as 816f0a0c200cffff or 0x816f0a0c200cffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0147

User Response

Information only; no action is required.

•

816f0a13-0301ffff : Bus [SensorElementName] has recovered from a Fatal Bus Error.

Chapter 6

Troubleshooting

579

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands