Lenovo Flex System x220 Installation And Service Manual Download Page 469

Page: 469 / 714

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

Information only; no action is required.

•

81010901-3702ffff : Numeric sensor PEN Inlet Temp going high (upper critical) has deasserted.

The previously high inlet temperature has returned to below its specified threshold.

May also be shown as 810109013702ffff or 0x810109013702ffff

Severity

Info

Serviceable

Automatically notify support

Alert Category

Critical - Temperature

SNMP Trap ID

CIM Information

Prefix:

PLAT

ID:

0495

User Response

Information only; no action is required.

•

81010902-0701ffff : Sensor [NumericSensorElementName] has detected that a voltage is no

longer high.

A previously high voltage has returned to below its specified threshold (sensor Planar 12V, Planar 3.3V, or
Planar 5V).

May also be shown as 810109020701ffff or 0x810109020701ffff

Severity

Info

Serviceable

Automatically notify support

Chapter 6

Troubleshooting

461

Summary of Contents for Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands

Lenovo Flex System x220, Installation And Service Manual

Search results

Summary of Contents for Flex System x220

Reviews:

Related manuals for Flex System x220

Brands by name

Popular brands