IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 101

Page: 101 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

311C

I2C Bus Panel Communication fault

I2CBUS
TWRCARD

4410

Internal Battery Power Unit Fault

Internal Battery Power Unit in the system has failed.

BATRY
BATCHGR
TWRCARD
CBLALL

4411

Internal Battery Power Unit Charger Fault

Internal Battery Power Unit Charger in the system has failed.

BATCHGR
TWRCARD
CBLALL

4412

Internal Battery Power Unit Charger Fault

Internal Battery Power Unit Charger in the system has failed.

BATCHGR
BATRY
TWRCARD
CBLALL

4413

Internal Battery Power Unit Charger Fault

Internal Battery Power Unit Charger in the system has failed.

BATCHGR
TWRCARD
CBLALL

4414

Battery Charger Load fault

PWROC
BATRY
TWRCARD
CBLALL

4415

Battery Power Unit missing

BATRY
TWRCARD
CBLALL

4416

Internal Battery Power Unit Charger Fault

BATCHGR
TWRCARD
CBLALL

4417

Battery Charger Unit missing

BATCHGR
TWRCARD
CBLALL

4500 to 4502

UPS Enable/Disable Failure

UPSUNIT
TWRCARD

4503

UPS CPM Failure

UPSUNIT
TWRCARD

4504

UPS Battery Failure

BATRY
UPSUNIT

4505

UPS Unit Failure

UPSUNIT
TWRCARD

4507

UPS Enable/Disable Failure

UPSUNIT
TWRCARD

4510

UPS Test Failure

UPSUNIT
TWRCARD

4513

UPS Interface Failure

UPSUNIT
TWRCARD

6018

One of the regulators has reported a fault

A regulator fault was detected.

PWRREG
BKSPCN

601A

One of the CPM regulators has reported a fault

A CPM regulator fault was detected.

PWRREG
BKSPCN
FI00030

1xxx

System Reference Codes

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands