IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 106

Page: 106 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

6B22

Disk Unit K19 regulator fault

The regulator that powers disk unit K19 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B23

Disk Unit K20 regulator fault

The regulator that powers disk unit K20 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B24

Disk Unit K21 regulator fault

The regulator that powers disk unit K21 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B25

Disk Unit K22 regulator fault

The regulator that powers disk unit K22 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B26

Disk Unit K23 regulator fault

The regulator that powers disk unit K23 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B27

Disk Unit K24 regulator fault

The regulator that powers disk unit K24 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B28

Disk Unit K25 regulator fault

The regulator that powers disk unit K25 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B29

Disk Unit K26 regulator fault

The regulator that powers disk unit K26 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B2A

Disk Unit K27 regulator fault

The regulator that powers disk unit K27 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B2B

Disk Unit K28 regulator fault

The regulator that powers disk unit K28 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B2C

Disk Unit K29 regulator fault

The regulator that powers disk unit K29 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B2D

Disk Unit K30 regulator fault

The regulator that powers disk unit K30 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B2E

Disk Unit K31 regulator fault

The regulator that powers disk unit K31 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B2F

Disk Unit K32 regulator fault

The regulator that powers disk unit K32 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6C00

Disk Unit 1 regulator fault

A fault detection failure occurred for the regulator that powers disk unit 1
or F01. The regulator or the ac module/SPCN card can cause this fault.

DISKTRY
BKSPCN

6C01

Disk Unit 2 regulator fault

A fault detection failure occurred for the regulator that powers disk unit 2
or F02. The regulator or the ac module/SPCN card can cause this fault.

DISKTRY
BKSPCN

1xxx

102

iSeries: iSeries 270, 800, 810, 820, 825, 830, 840, 870, 890, SB2, and SB3 Analyze Hardware Problems (System Reference

Codes)

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands