IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 135

Page: 135 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9117

SPCN - Control Panel interface is now working.

The SPCN to control panel interface is now working.

No action required. This reference code is logged for information only.

91DD

All SPCN Downloads Complete

9212

Frame Address field not valid.

A Licensed Internal Code command had a frame address that is not valid.

Exchange the failing items for the failing node.

TWRCARD

9213

Invalid Address status, secondary node.

The address in the SPCN command does not match the assigned address of
the secondary node.

Exchange the failing items for the failing node.

TWRCARD

9214

Invalid Address Mode status

Invalid Address Mode occurred during Frame Command processing.

TWRCARD
AJDG301

9215

Invalid Frame Command status

Invalid Frame Command occurred during Frame Command processing.

TWRCARD
AJDG301

921B

System Unit SPCN Port Fault status.

System Unit Port Fault occurred during Command processing.

TWRCARD
AJDG301

922B

Address Unassigned status

A secondary node has no address assigned during Command processing.

TWRCARD
AJDG301

9231

Frame-to-Frame Communications Failure

A frame-to-frame communications failure occurred during STF processing.

TWRCARD
CBLALL

9232

Intrarack Communications Failure

An SPCN secondary node to frame communications failure occurred
during Command processing.

TWRCARD
CBLALL

9233

Intrarack Communications Failure

An SPCN frame to secondary node communications failure occurred
during Command processing.

TWRCARD
CBLALL

9234

Unsupported Packet Size status

Unsupported Packet Size occurred during STF and Secondary Node
Command processing.

TWRCARD
CTLPNL
SVCPROC

9235

SPCN Secondary Node Timeout status

An SPCN Secondary Node Timeout occurred during Command processing.

If the failing secondary node is in a 9337, go to the “Analyzing Problems”
section in the

9337 Disk Array Service Information

manual.

TWRCARD
AJDG301
CBLALL

9236

Frame Timeout status

An SPCN Frame Node Timeout occurred during Network post processing.

TWRCARD
CBLALL

9238

Secondary Node Fault

An SPCN Secondary Node Fault occurred during Command processing.

TWRCARD
AJDG301

1xxx

System Reference Codes

131

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands