IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 103

Page: 103 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

6718

Regulator fault

Regulator 1 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

671A

Regulator fault

PWRREG
BKSPCN
FI00030

6738

Regulator fault

Regulator 2 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

673A

Regulator fault

Regulator 18 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN
FI00030

6758

Regulator fault

Regulator 3 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
ACMODUL

6818

One of the regulators has reported a fault

A fault detection failure occurred for a regulator. The regulator or the ac
module/SPCN card can cause this fault.

PWRREG
BKSPCN

6918

One of the regulators has reported a fault

An over current fault detection failure occurred for a regulator. The
regulator or the ac module/SPCN card can cause this fault.

PWRREG
BKSPCN

6A18

Regulator Fault

A regulator fault detection failure occurred for regulator 1. The ac module
or the regulator can cause this fault.

PWRREG
BKSPCN
BACKPLN

6A38

Regulator Fault

A regulator fault detection failure occurred for regulator 2. The regulator or
the ac module/SPCN card can cause this fault.

PWRREG
BKSPCN
BACKPLN

6A58

Regulator Fault

A regulator fault detection failure occurred for regulator 3. The regulator or
the ac module/SPCN card can cause this fault.

PWRREG
ACMODUL
BACKPLN

6B00

Disk Unit 1 regulator fault

The regulator that powers disk unit 1 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B01

Disk Unit 2 regulator fault

The regulator that powers disk unit 2 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B02

Disk Unit 3 regulator fault

The regulator that powers disk unit 3 reported a fault.

DISKTRY
DISKDRV
BKSPCN

6B03

Disk Unit 4 regulator fault

The regulator that powers disk unit 4 reported a fault.

DISKTRY
DISKDRV
BKSPCN

1xxx

System Reference Codes

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands