IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 174

Page: 174 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9211

Gateway device detected a bus protocol error

Use the gateway device service documentation to analyze the problem.

FCGATE
FCIOA
FI00851
ANYFC
FCCABLE
EXTSCSI
61G8324

9300

Tape unit failure

FI00851

9301

Tape device failure, redundancy lost

The tape unit detected a hardware failure that does not prevent the tape
unit from completing the present operation.

See the 3590 Tape Unit service information to determine the failing item.

FI00851

9302

I/O processor Licensed Internal Code error

If the system is operational, take a dump of the I/O processor data. For
more information, see the

iSeries Service Functions

information or ask your

next level of support for assistance.

FI00130

9303

Gateway device failure

Use the gateway device service documenation to analyze the problem.

FCGATE

9310

Licensed Internal Code for the tape unit is not correct

FI00851
FI00130

9320

Tape device Licensed Internal Code failure

Do the following:

Take a dump of the tape device Licensed Internal Code (see the 3590
Tape Unit service information).

Power off the tape unit. Then power on the tape unit to resume
operation.

FI00130
FI00851

9321

Gateway device Licensed Internal Code error

Use the gateway device service documenation to analyze the problem.

FCCODE

9350

Tape unit detected a read or write error on tape medium

A permanent read or write error occurred, and the tape unit determined
that the tape cartridge is defective. Exchange the tape cartridge.

MHQTMED
UHQCLN
FI00851

9351

Tape with excessive error rate was mounted in tape device.

The tape unit detected that the installed tape cartridge has a history of
excessive read and write errors. It is recommended that you exchange the
tape cartridge.

MHQTMED
UHQCLN
FI00851

9355

The data format is incorrect; the tape cannot be read

The tape device does not give support to the data format on the tape
cartridge. Format the tape cartridge again or use a different tape cartridge.

See the

3590 Tape Drive Operator’s Guide

for instructions on formatting a

tape cartridge.

MHQTMED
UHQCLN
FI00851

9500

I/O processor Licensed Internal Code error

If the system is operational, take a dump of the I/O processor data. For
more information, see the

iSeries Service Functions

information or ask your

next level of support for assistance.

FI00130

3590

170

iSeries: iSeries 270, 800, 810, 820, 825, 830, 840, 870, 890, SB2, and SB3 Analyze Hardware Problems (System Reference

Codes)

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands