IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 71

Page: 71 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

9234

Unsupported Packet Size status

Unsupported Packet Size occurred during STF and Secondary Node
Command processing.

TWRCARD
CTLPNL
SVCPROC

9235

SPCN Secondary Node Timeout status

An SPCN Secondary Node Timeout occurred during Command processing.

If the failing secondary node is in a 9337, go to the “Analyzing Problems”
section in the

9337 Disk Array Service Information

manual.

TWRCARD
AJDG301
CBLALL

9236

Frame Timeout status

An SPCN Frame Node Timeout occurred during Network post processing.

TWRCARD
CBLALL

9238

Secondary Node Fault

An SPCN Secondary Node Fault occurred during Command processing.

TWRCARD
AJDG301

9239

Frame Node Fault

An internal error in the SPCN frame node prevents the running of a Frame
command.

TWRCARD
AJDG301

923A

ASA Failure

The frame address returned by a secondary node does not match the
address of the frame.

TWRCARD
AJDG301

923B

Invalid Packet Length for data sent.

An Invalid Packet Length occurred for data exchanged.

AJDG301
TWRCARD

9280

Response Stack Overflow

Too many responses were received during System Frame command
processing.

CBLALL
AJDG301
TWRCARD

9281

Response Overrun

Response Overrun occurred during System Frame processing.

CBLALL
AJDG301
TWRCARD

9282

No Free Entries

No free entries were found during System Frame processing.

CBLALL
AJDG301
TWRCARD

9283

ARA Failure

An Assign Frame Address Failure occurred during ARA Preprocessing.

TWRCARD
AJDG301

9284

Undefined status

Undefined Status occurred during Frame or STF processing.

TWRCARD
AJDG301

9285

BCC Fault

A BCC Error was detected during Network post processing.

TWRCARD

9286

Length Check Error.

Length Check occurred during SPCN post processing.

TWRCARD
AJDG301

9287

Undefined status

Undefined Status occurred during Command processing.

TWRCARD
AJDG301

9288

Configuration Error

A configuration error was detected during System Frame processing.

TWRCARD
AJDG301

1xxx

System Reference Codes

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands