IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 47

Page: 47 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

6C2B

Disk Unit K28 regulator fault

A fault detection failure occurred for the regulator that powers disk unit
K28.

DISKTRY
BKSPCN

6C2C

Disk Unit K29 regulator fault

A fault detection failure occurred for the regulator that powers disk unit
K29.

DISKTRY
BKSPCN

6C2D

Disk Unit K30 regulator fault

A fault detection failure occurred for the regulator that powers disk unit
K30.

DISKTRY
BKSPCN

6C2E

Disk Unit K31 regulator fault

A fault detection failure occurred for the regulator that powers disk unit
K31.

DISKTRY
BKSPCN

6C2F

Disk Unit K32 regulator fault

A fault detection failure occurred for the regulator that powers disk unit
K32.

DISKTRY
BKSPCN

7000 to 7004

Air Moving Device Fault

A problem was detected with an Air Moving Device which can be caused
by an Air Moving Device not being installed or operating at the wrong
speed.

AIRMOVR
BKSPCN

7101

Power supply failure

The ac power supply module reported a fault. One of the other power
supplies may also cause this error.

PWRSPLY

7102

Power supply failure

Feature power supply 2 reported a fault. An ac module or one of the other
feature power supplies may also cause this error.

PWRSPLY
ACMODUL

7103

Power supply failure

Feature power supply 1 reported a fault. The ac module or one of the other
feature power supplies may also cause this error.

PWRSPLY
ACMODUL

7201

Power Supply over current fault

The ac module reported an over current condition. This is usually caused
by one of the regulators.

Perform SPCN-PIP10.

PWRREG
PWRSPLY
ACMODUL

7202

Power Supply over current fault

Feature power supply 2 reported an over current condition. This is usually
caused by one of the regulators.

Perform SPCN-PIP10.

PWRREG
PWRSPLY
ACMODUL

7203

Power Supply over current fault

Feature power supply 1 reported an over current condition. This is usually
caused by one of the regulators.

Perform SPCN-PIP10.

PWRREG
PWRSPLY
ACMODUL

1xxx

System Reference Codes

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands