IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 39

Page: 39 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

6338

Regulator Fault

Regulator 2 reported a fault.

PWRREG
BKSPCN

633A

Regulator Fault

Regulator 2 reported a fault.

PWRREG
ACMODUL
FI00030

6358

Regulator Fault

A regulator 3 reported a fault.

PWRREG
ACMODUL

6400 to 6401

Power Good Fault

PGDPART
FI00065
BKSPCN

6518

One of the regulators has reported a fault

An over current sensor failure occurred for a regulator. The ac module or
one of the regulators can cause this fault.

PWRREG
BKSPCN

6618

Regulator over current fault

Regulator 1 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

6638

Regulator over current fault

Regulator 2 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

6658

Regulator over current fault

Regulator 3 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
ACMODUL

6718

Regulator fault

Regulator 1 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

671A

Regulator fault

PWRREG
BKSPCN
FI00030

6738

Regulator fault

Regulator 2 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

673A

Regulator fault

Regulator 18 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN
FI00030

6758

Regulator fault

Regulator 3 reported a fault.

Fault tolerance may allow continued system operation.

PWRREG
ACMODUL

1xxx

System Reference Codes

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands