IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 102

Page: 102 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

6118

Regulator over current fault

One of the regulators detected an over current condition. This may be
caused by the regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6218

Regulator over current fault

Regulator 1 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6238

Regulator over current fault

Regulator 2 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6258

Regulator over current fault

Regulator 3 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
ACMODUL

6318

Regulator Fault

Regulator 1 has reported a fault.

PWRREG
BKSPCN

631A

Regulator Fault

Regulator 1 has reported a fault.

PWRREG
ACMODUL
FI00030

6338

Regulator Fault

Regulator 2 reported a fault.

PWRREG
BKSPCN

633A

Regulator Fault

Regulator 2 reported a fault.

PWRREG
ACMODUL
FI00030

6358

Regulator Fault

A regulator 3 reported a fault.

PWRREG
ACMODUL

6400 to 6401

Power Good Fault

PGDPART
FI00065
BKSPCN

6518

One of the regulators has reported a fault

An over current sensor failure occurred for a regulator. The ac module or
one of the regulators can cause this fault.

PWRREG
BKSPCN

6618

Regulator over current fault

Regulator 1 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

6638

Regulator over current fault

Regulator 2 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
BKSPCN

6658

Regulator over current fault

Regulator 3 reported a false over current condition.

Fault tolerance may allow continued system operation.

PWRREG
ACMODUL

1xxx

iSeries: iSeries 270, 800, 810, 820, 825, 830, 840, 870, 890, SB2, and SB3 Analyze Hardware Problems (System Reference Codes)

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands