IBM iSeries Series Analyze Hardware Problems (System Reference Codes Download Page 38

Page: 38 / 306

Reference Code

Description/Action Perform all actions before exchanging Failing Items

Failing Item

4415

Battery Power Unit missing

BATRY
TWRCARD
CBLALL

4416

Internal Battery Power Unit Charger Fault

BATCHGR
TWRCARD
CBLALL

4417

Battery Charger Unit missing

BATCHGR
TWRCARD
CBLALL

4500 to 4502

UPS Enable/Disable Failure

UPSUNIT
TWRCARD

4503

UPS CPM Failure

UPSUNIT
TWRCARD

4504

UPS Battery Failure

BATRY
UPSUNIT

4505

UPS Unit Failure

UPSUNIT
TWRCARD

4507

UPS Enable/Disable Failure

UPSUNIT
TWRCARD

4510

UPS Test Failure

UPSUNIT
TWRCARD

4513

UPS Interface Failure

UPSUNIT
TWRCARD

6018

One of the regulators has reported a fault

A regulator fault was detected.

PWRREG
BKSPCN

601A

One of the CPM regulators has reported a fault

A CPM regulator fault was detected.

PWRREG
BKSPCN
FI00030

6118

Regulator over current fault

One of the regulators detected an over current condition. This may be
caused by the regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6218

Regulator over current fault

Regulator 1 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6238

Regulator over current fault

Regulator 2 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
BKSPCN

6258

Regulator over current fault

Regulator 3 detected an over current condition. This may be caused by the
regulator or one of cards powered by the regulator.

PWRREG
ACMODUL

6318

Regulator Fault

Regulator 1 has reported a fault.

PWRREG
BKSPCN

631A

Regulator Fault

Regulator 1 has reported a fault.

PWRREG
ACMODUL
FI00030

1xxx

iSeries: iSeries 270, 800, 810, 820, 825, 830, 840, 870, 890, SB2, and SB3 Analyze Hardware Problems (System Reference Codes)

Summary of Contents for iSeries Series



















































































































































































































































































































Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands

IBM iSeries Series, Analyze Hardware Problems (System Reference Codes

Search results

Summary of Contents for iSeries Series

Reviews:

Related manuals for iSeries Series

Brands by name

Popular brands