Fagor CNC 8060, Installation Manual

Page: 30 / 698

Installation manual.
CNC 8060
CNC 8065
·30·
(R
EF
: 1709)
Ref. 1512
Variables related to CNC status.
• Detailed CNC status in automatic mode. New value $100000. • Variable: (V.)G.CNCAUTSTATUS
Variables associated with the analog inputs and outputs.
• Volts of the local analog output [n] (only at the 8060).
• Volts of output [n] of the RCS-S module.
• Variable: (V.)G.ANALO[n]
• Variable: (V.)G.ANASO[n]
Variables related to the programmed functions.
• Withdraw the axes after interrupting an electronic threading. • Variable: (V.)G.RETREJ
Variables related to functions.
• System spindles involved in the subroutine associated with M3, M4, M5,
M19 and M41-M44.
• Variable: (V.)G.SUBMSPDL
Variables related to canned cycles.
• Active canned cycle. • Variable: (V.)G.ACTIVECYLE
Variables related to the probe.
• Status of probe ·1·.
• Probing movement. Value measured at the master spindle of the channel.
• Variable: (V.)G.PRBST
• Variable: (V.)G.PLMEAS4
Variables related to axis and spindle repositioning.
• End of axis and spindle repositioning at the starting point.
• End of axis and spindle repositioning at the interruption point.
• Variable: (V.)G.ENDREPINI
• Variable: (V.)G.ENDREPINT
Variables related to synchronized switching.
• Time remaining to activate the laser output.
• Time remaining to deactivate the laser output.
• Variable: (V.)G.LASEROTMON
• Variable: (V.)G.LASEROTMOFF
PWM related variables
• Amount of time that PWM stays active in burst mode.
• Final PWM status once burst mode is over.
• Variable: (V.)G.PWMBTIME
• Variable: (V.)G.PWMBEND
Variables related to cycle time.
• Percentage of loop time (cycle time) used by the PLC.
• Percentage of loop time (cycle time) used by the dynamic preparation of
the tool path.
• Variable: (V.)G.PLCTIMERATE
• Variable: (V.)G.TRAYTIMERATE
Variables related to the feedback inputs.
• Value of the local count-up 1 input.
• Value of the local count-up 2 input.
• Variable: (V.)G.LCOUNTER1
• Variable: (V.)G.LCOUNTER2
Feedrate related variables.
• Actual (real) CNC feedrate in G95.
• Real feedrate on the tool path.
• Feedrate active in the block.
• Variable: (V.)G.FREALPR
• Variable: (V.)G.ACTFEED
• Variable: (V.)G.IPOFEED
Variables related to the active tool and to the next one.
• Active tool. Code of the tool offset type. • Variable: (V.)TM.TOOLTYP[ofd]
Variables associated with the tool being prepared.
• Tool being prepared. Code of the tool offset type.
• Tool being prepared. Tool-holder orientation.
• Variable: (V.)G.TOOLTYP
• Variable: (V.)G.FIXORI
Variables related to the kinematics and coordinate transformation.
• Solution 2 is selected in instruction #CS or #ACS. • Variable: (V.)G.TORISOL2
General variables of the CNC.
• CNC model.
• CNC sub-version number (decimal value).
• Variable: (V.)G.CNCMODEL
• Variable: (V.)G.SUBVERSION
Variables associated with the part-program being executed.
• Number of the line of the program where the cursor is. • Variable: (V.)G.CURSORLINE
Variables related to the machine parameters of the channels.
• Orientation smoothing of the rotary axes working with RTCP. • Variable: (V.)MPG.ORISMOOTH
Variables related to managing the feedrate in HSC mode.
• Amount of error allowed on the axis for the HSC mode. • Variable: (V.)A.ACTROUND.xn
Software V05.40
The maximum number of axes that can be programmed is now 32 instead of
28. • Machine parameter: NAXIS.
The maximum number of spindles is now 6 instead of 4. • Machine parameter: NSPDL.
The maximum number of axes depends on the number of spindles, the sum
of axes plus spindles being 32 at the most.
Work zones. • Machine parameter: ZONELIMITTOL.
• PLC mark: LIM(axis)OFF.
• Variable: (V.)G.ZONEST[k]
(V.)G.ZONETOOLWATCH[k]
(V.)G.ZONEWARN[k]
(V.)A.ZONELIMITTOL.xn
(V.)A.ZONELOWLIM[k].xn
(V.)A.ZONEUPLIM[k].xn
(V.)G.ZONECIR1[k]
(V.)G.ZONECIR2[k]
(V.)G.ZONER[k]
(V.)G.ZONECIRAX1[k]
(V.)G.ZONECIRAX2[k]
Home search mode for position-Sercos axes. • Machine parameter: REFMODE.
Tandem axes. Torque control mode. • Machine parameter: TORQMODE.
Software V05.31