Fagor CNC 8060 Page 217 Installation Manual Download | Manualshive

Page: 217 / 698

background image

Installation manual.

CNC 8060
CNC 8065

MACHINE PA

RAMETERS.

2.

Mac

h

ine parameters for

the

axes. Work sets.

·217·

(R

EF

: 1709)

CURVJERK
Maximum contouring Jerk permitted.

Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values (1): De 0 a 1E+009 mm/s³.
Possible values (2): De 0 a 39370078.74016 inch/s³.
Possible values (3): De 0 a 1E+009 grados/s³.
Default value: 0.
Associated variable: (V.)[ch].MPA.CURVJERK[set].xn

If this parameter is set with a ·0· value, the maximum jerk of the axis is respected.

FASTACC
Maximum acceleration permitted (FAST mode).

Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values (1): From 0 to 100000.0000 mm/s².
Possible values (2): From 0 to 3937.00787 inch/s².
Possible values (3): From 0 to 100000.0000 grados/s².
Default value: 0.
Associated variable: (V.)[ch].MPA.FASTACC[set].xn

If this parameter is set with a ·0· value, the maximum acceleration of the axis is respected.

MAXERROR
Position error.

Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Possible values (1): From 0 to 9999.99999 mm.
Possible values (2): From 0 to 3937.00787 inch.
Possible values (3): From 0 to 9999.99999 degrees.
Default value: 0.1000 mm / 0.00394 inch / 0.1000 grados.
Associated variable: (V.)[ch].MPA.MAXERROR[set].xn

Maximum axis position error in HSC when working outside the plane/trihedron.

CONTERROR
Tolerance per axis for smoothing the generated n-dimensional
path.

Parameter valid for linear and rotary axes and spindles.
Parameter valid for analog drive, Sercos and simulated.
Default value: 0.1000 mm/º.
Associated variable: (V.)[ch].MPA.CONTERROR[set].xn

For 5-axis machining, this parameter may be used to set the tolerance per axis for smoothing
the generated n-dimensional path. This parameter does not affect the 3D error when working
with RTCP. We recommend setting this parameter on rotary axes.

«
...
215
216
217
218
219
...
»

Summary of Contents for CNC 8060



























































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for CNC 8060

Brand: National Instruments Pages: 48

Brand: Omega Lift Pages: 8

Brand: HANYOUNG NUX Pages: 2

Brand: Ulvac Pages: 87

Brand: tacwise Pages: 12

Brand: Omer Pages: 26

Brand: H3C Pages: 5

Brand: Parkside Pages: 45

Brand: Bluerock Tools Pages: 20

Brand: HARDELL Pages: 8

Brand: Cobra Pages: 12

Brand: Harman Pages: 76

Brand: Kaboodle Pages: 2

Craftsman 113.213850

Brand: Sears Pages: 24

Brand: Kärcher Pages: 68

Brand: Far Tools Pages: 52

Brand: Premier Pages: 4

Brand: Yost Vises Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands